BNL, Upton, New York, USA
Fermilab, Batavia, Illinois, USA
ANL, Lemont, Illinois, USA
A new magnetic measurement system is under construc-tion at BNL for accurate field harmonic measurements and fiducialization of magnets for a future upgrade of the NSLS- II storage ring. The entire storage ring is envi-sioned to be replaced with a new lattice concept, known as Complex Bend, which superimposes dipole and high-gradient quadrupole fields. The magnetic measurement system will use rotating wire and a PCB rotating coil specifically designed for small-aperture (< 15 mm) high gradient magnets. In this paper we describe in detail the mechanical design and the data acquisition hardware and software.
ANL, Lemont, Illinois, USA
The Advanced Photon Source Upgrade (APS-U) accelerator magnets have stringent stability requirement*. The project schedule and budget did not allow for full prototyping of the final design. Therefore, the engineers relied on accurate simulation to ensure that the design would meet the specifications. Recently, assembly and free-boundary vibration tests have been done on the first article of the upstream quadrupole Doublet, Longitudinal gradient dipole and Multipole module (DLM-A). The top surface flatness of the girder and the magnet alignment measurement results demonstrate the static positioning requirement of magnet-to-magnet is met. The free-boundary condition modal test results were used to validate the FEA analysis used in the DLM-A design. This validation then confirms the predicted performance of the magnet support system design. Mode shapes and corresponding frequencies from the FEA modal analysis agree with the experimental modal analysis within an acceptable tolerance. The validation approves not only the procedure for accurate modeling of magnet support system that APS-U has developed, but also provides confidence in predicting the accelerator performance.
*Advanced Photon Source. (2019). APS Upgrade Project Final Design Report (APSU-2.01-RPT-003). Retrieved from https://www.aps.anl.gov/APS-Upgrade/Documents
SOLEIL, Gif-sur-Yvette, France
|
Right click on video for Picture-in-Picture mode or Full screen display. At start the sound is muted! |
SESAME, Allan, Jordan
Elettra-Sincrotrone Trieste S.C.p.A., Basovizza, Italy
ESRF, Grenoble, France
NSRC SOLARIS, Kraków, Poland
The BEAmline for Tomography at SESAME (BEATS) will operate an X-rayμtomography station providing service to scientists from archaeology, cultural heritage, medicine, biology, material science and engineering, geology and environmental sciences*. BEATS will have a length of 45 m with a 3-pole-wiggler source (3 T peak magnetic field at 11 mm gap). Filtered white and monochromatic beam (8 keV to 50 keV, dE/E: 2% to 3% using a double-multilayer-monochromator) modalities will be available. In this work we present the beamline optical design, verified with simulation tools included in OASYS**. The calculated flux through 1 mm2 at the sample position will be as high as 8.5×109 Ph/s/mm2 in 0.1% of the source bandwidth, for a maximum usable beam size of 70×15 mm2. Beam transverse coherence will be limited to below 1 µm by the horizontal size of the X-ray source (~2 mm FWHM). For phase contrast applications requiring enhanced coherence, front end slits can be closed to 0.5 mm horizontally, with a reduction of the available beam size and photon flux. The BEATS beamline will fulfill the needs of the tomography community of SESAME.
* H2020 project BEATS, Technical Design Report (July 2020).
** L. Rebuffi and M. Sanchez del Rio, Proc. SPIE 10388: 130080S (2017).
ANL, Lemont, Illinois, USA
The Advanced Photon Source-Upgrade (APS-U) project* is under construction and will incorporate a new Multi-Bend Achromat (MBA) lattice. With this design, the new storage ring will require over 1320 new magnets that are being produced under build-to-print contracts to several vendors across the globe. Magnetic measurements are needed to characterize and fiducialize all these magnets to ensure field quality and alignment requirements are met. Seven specialized test benches were designed and built to meet the measurement requirements. These measurement benches may be classified into two groups. The first group is the field quality measurement that includes the strength of the main field and higher harmonics. The multipole magnets are measured using four rotating coil benches, whereas the longitudinal gradient dipoles are mapped using a Hall probe system. The second group is fiducialization that locates the magnetic center of the magnet using a rotating wire and relates it to magnet fiducials and reference surfaces using a laser tracker. This information accompanies each magnet through the module assembly and final installation in the ring to ensure that the magnet is aligned within the allowable tolerance. To date, about 65% of all magnets needed for the storage ring have been measured and fiducialized. Mechanical design of the measurement benches will be presented.
*Advanced Photon Source. (2017). APS Upgrade Project Preliminary Design Review Report (APSU-2.01-RPT-002). Retrieved from https://www.aps.anl.gov/APS-Upgrade/Documents.
ANL, Lemont, Illinois, USA
APS Upgrade selected the horizontal injection scheme which requires exchanging the x and y emittances in the BTS transport line through a series of six skew quadrupoles, as well as matching the beam parameters to the APS Upgrade storage ring through two dipoles and a conventional pulsed septum. This paper presents the layout of this BTS line section in the storage ring tunnel and key components in this section including the mechanical design of dipole magnet, quadrupole and skew quad magnets, the vacuum system, the diagnostics system, and the supports. Finally, detailed mechanical design of this BTS line section in modules and some consideration for fabrication and installation are addressed.